OmniConverter® 10GPoEBT/M

Managed 6 Port 60/100W IEEE 802.3bt 10Gigabit Ethernet Switches



Features


  • Managed 1/10G 60W and 100W PoE Ethernet Switch
  • Two 1/10G SFP/SFP+ transceiver uplink ports
  • Supports copper and fiber SFP transceivers
  • Supports 10M, 100M, 1G and 10Gbps copper SFP/SFP+ transceivers
  • Four 10/100/1000 copper 60W or 100W PoE user ports
  • Supports jumbo frames up to 10,240 bytes
  • Heartbeat signal to verify connectivity to the PD
  • Configurable PoE Power Reset
  • PoE power management with LLDP MED and MDI TLV, and PoE Power Multi-Day Scheduler
  • Management via Web, Telnet, SSH, SNMPv1/v2c/v3 and serial interfaces
  • Easy to use Hierarchical Command Line Interface
  • SNMP management via Omnitron’s NetOutlook® management software, or third-party SNMP software
  • Supports IPv4 and IPv6
  • IEEE 802.1x, RADIUS, TACACS+ and ACL
  • Email Notification
  • Dual Device mode for operating as two separate switches
  • Directed Switch mode AKA Camera mode to prevent port flooding
  • AC to DC Power Adapter or 2-Pin DC terminal
  • Wall, Rack and DIN-rail mountable
  • Commercial (0º to 50ºC), wide (-40º to 60ºC) and extended (-40º to 75ºC) operating temperature ranges
  • TAA, BAA and NDAA compliant, and Made in the USA
  • Free 24/7/365 Technical Support

ADDITIONAL FEATURES

  • Rapid and Multiple Spanning Tree Protocol
  • IEC 62439-2 Industrial Ring Media Redundancy
  • IEEE 802.1ax LAG and LACP; Active/Active and Active/Standby
  • IPv4 Internet Group Management (IGMP) and IPv6 Multicast Listener Discovery (MLD) snooping
  • DHCP Relay Option 82, DHCPv6 and DHCPv6 Relay
  • IEEE 802.1ab Link Layer Discovery Protocol
  • Rate Limiting, Queue prioritization and Class of Service
  • IEEE 802.1Q VLAN tagging and IEEE 802.1ad Q-in-Q
  • Broadcast / Multicast / Unicast Storm Prevention
  • Static MAC configuration and blocking of unknown Unicast/Multicast addresses
  • SNTP / NTP and time of day




Description


The OmniConverter 10GPoEBT/M are managed Ethernet switches that feature two 1/10G uplink ports and four 10/100/1000 RJ-45 copper Power Sourcing Power-over-Ethernet user ports. The 10GPoEBT/M is an IEEE 802.3bt switch featuring 60W and 100W per user port models.

All models support Directed Switch mode, which directs multicast traffic (such as video) only to the appropriate uplink port, preventing multicast traffic from flooding other network ports.

The switches support redundant uplinks, industrial ring Media Redundancy Protocol (MRP), Spanning Tree protocol and daisy-chain configurations for high availability industrial network applications.

The switches support Dual Device mode that enables the 10GPoEBT/M to operate as two independent and isolated Ethernet switches.

The mode of operation can be configured using easily accessible DIP-switches or using Web, Telnet, SSH, SNMPv1/v2c/v3 or Serial Console management interfaces. IPv4 and IPv6 are supported on the switches. These management interfaces provide access to filtering and security options, such as, broadcast storm prevention, IGMP, IEEE 802.1x, RADIUS, TACACS+ and Access Control Lists. Email notification and alarm reporting is provided.

The OmniConverter switches are available with Small Form Pluggable (SFP) transceiver receptacle ports. The SFP ports support 10/100/1000BASE-T, 1000BASE-T and 10GBASE-T copper transceivers. They also support 1G and 10G multimode or single-mode fiber, dual or singlefiber and standard, CWDM and DWDM wavelengths.

The switches feature a Remote PoE Power Reset function that enables the user to remotely power-cycle and reset each PD. They also feature a configurable Heartbeat Reset function that automatically pings the attached PDs and automatically power cycles and resets the PDs when detecting a heartbeat loss. The Remote Power Reset and the Heartbeat Reset functions save time and expense by eliminating the need to dispatch manpower to remote network sites.

All models can be wall mounted, rack mounted using a shelf or DIN-rail mounted using DIN-rail mounting clips. They are available with an external 100 to 240V AC power adapter or with a DC terminal connector.





Examples


Dual Device Mode Application

This Dual Device feature is extremely useful when two isolated networks domains share a single network distribution location.

The example below depicts a scenario where a surveillance security (green) network and a Wi-Fi (purple) network are sharing a single hub distribution location. Using the two uplinks and the Dual Switch mode facilitates using a single PoE switch driving both the Cameras and the Wi-Fi Access Points while maintaining isolation between the networks.

Dual Media Converter Mode 3160 10gpoebt m

Daisy-Chain and Ring Topology Network Application

This example demonstrates the daisy chaining and ring capabilities of the OmniConverter. In this application each OmniConverter switch connects to its neighboring switches via its uplink ports eventually closing the ring.

Using this network architecture combined with ring protection protocols such as Media Redundancy Protocol (MRP) or Rapid Spanning Tree Protocol (RSTP) facilitates a highly resilient network required in mission critical applications.

Dasiy Chain Application 3160 10gpoebt m

PoE Power Multi-Day Scheduler

The web management allows you to automatically power on/off connected PD devices at pre-defined times of the day, which conserves energy and increases network security.  For example, network managers can schedule to turn off power to their VoIP phones or WiFi Devices after business hours preventing unauthorized access and conserving energy, while having continuous PoE power to their Security Surveillance cameras 24 hours a day.

poe-scheduling





Specifications


Description OmniConverter® 10GPoEBT/M
10/100/1000BASE-T with 1/10G Gigabit Fiber
Managed 6 Port IEEE 802.3bt 60/100W PoE Ethernet Switch
Standard Compliances

IEEE 802.3, IEEE 802.1Q, IEEE 802.1ad, IEEE 802.1ab, IEEE 802.1ax, IEEE 802.1w RSTP/MSTP

RFC 5424, RFC 4541, RFC 2710

IEC 624339-2,

SMTP, SNTP, RADIUS, TACACS+, IEEE 802.1x

IEEE 802.3af (15.40 watts), IEEE 802.3at (30 watts)

IEEE 802.3bt (60 and 100 watts)

Regulatory Compliances (*Pending) 

Safety*: UL 62368-1, UL 60950-1,

              IEC 62368-1, IEC 60950-1,

              EN 62368-1, EN 60950-1,

              CAN/CSA C22.2 No. 62368-1-14, CAN/CSA C22.2 No. 60950-1,

              CE Mark, UKCA

EMC:     EN 55032/24 CE Emissions/Immunity,

              IEC 61000-6-4 Industrial Emissions, IEC 61000-6-2 Industrial Immunity

EMI:      CISPR 32,

              FCC 47 Part 15 Subpart B Class A

EMS:     IEC 61000-4-2 ESD: Contact: 6 kV; Air: 8 kV,

              IEC 61000-4-3 RS: 80 MHz to 1 GHz: 10 V/m,

              IEC 61000-4-4 EFT: Power: 2 kV; Signal: 1 kV (DC models),

              IEC 61000-4-4 EFT: Power: 1 kV; Signal: 1 kV (AC models),

              IEC 61000-4-5 Surge: Power: 2 kV; Signal: 2 kV (DC models),

              IEC 61000-4-5 Surge: Power: 1 kV Line/Line; 2 kV Line/Gnd; Signal: 2 kV (AC models),

              IEC 61000-4-6 CS: Signal: 10 V, IEC 61000-4-8 (Magnetic Field) 30A/m,

              IEC 61000-4-11 (Voltage Dips, interrupts)

IP Rating: IP20 Protection

ACT: TAA, BAA, NDAA 

Environmental REACH, RoHS and WEEE
Management

IPv4 and IPv6 address

Web, Telnet, SSH, SNMPv1/v2c/v3

In-Band management via Ethernet port

Out-of-band management via serial port

PoE Modes IEEE Alternate A (Alt A) and 4-Pair
Frame Size Up to 10,240 bytes
Port Types

Copper:          10/100/1000BASE-T (RJ-45)

SFP/SFP+:    10GBASE-X Fiber Transceivers

                      10GBASE-T Copper Transceivers

                      1000BASE-X Fiber Transceivers

                      1000BASE-T Copper Transceivers

                      10/100/1000BASE-T SGMII Copper Transceivers

Serial:            RS-232 (RJ-45)

Cable Types

Copper: EIA/TIA 568A/B, Cat 5 UTP and higher

Fiber:     Multimode: 50/125, 62.5/125µm

              Single-mode: 9/125µm

Serial:    Category 3 and higher

AC Power Requirements
(Models with AC/DC Adapters)

100 - 240VAC/50 - 60Hz

3.5A max at 115VAC

2.5A max at 230VAC

Supplied adapter provides 250W

DC Power Requirements
(Models with DC Terminals)

60W Models:

+46 to +57VDC;

4.47A @ 56VDC

2 Pin Terminal (isolated)

100W Models:

+46 to +57VDC;

7.33A @ 56VDC

2 Pin Terminal (isolated)

Dimensions
(W x D x H)
6.28” x 5.2” x 1.5” (159.5 mm x 132.1 mm x 38.1 mm)
Weight Module Only: 1.6 lb. (735 grams)
Module with AC/DC Adapter: 3.7 lbs. (1703 grams)
Operating Temperature Commercial: 0 to 50°C
Wide: -40 to 60°C (-20°C AC cold start)
Extended: -40 to 75°C - not available for models with AC/DC power adapter
Storage: -40 to 80°C
Humidity 5% to 95% (non-condensing)
Altitude -100m to 4,000m (operational)
MTBF (hrs) Module Only: 272,000
AC/DC Adapter: 100,000
Warranty 5 year product warranty with 24/7/365 free Technical Support
2 year AC power adapter warranty

 

AC/DC Adapter Temperature Derating - Total Available Wattage to RJ-45 Ports
Model Watts Required 40°C 50°C 60°C
10GPoEBT/M 60W 240 watts Full Power 175 watts 115 watts
10GPoEBT/M 100W 400 watts 240 watts 175 watts 115 watts
The AC/DC Adapter Temperature derating table is not applicable to models with DC Terminal (see Ordering table for Direct DC -9 option). The DC Terminal models will provide full PoE power over the operating temperature range of the module as long as the DC input voltage meets the requirements stated in the specification table.

 

Power / Voltage Requirements and Specifications

Description

15W

IEEE 802.3af PoE

30W

IEEE 802.3at PoE+

60W

IEEE 802.3.bt PoE
(Type 3)

100W

IEEE 802.3bt PoE
(Type 4)

Power Supply Voltage Range 46.0 to 57.0 VDC 51.0 to 57.0 VDC 51.0 to 57.0 VDC 53.0 to 57.0 VDC
Voltage Range at PSE port Output 44.0 to 56.0 VDC 50.0 to 56.0 VDC 50.0 to 56.0 VDC 52.0 to 56.0 VDC
Maximum Power from PoE/PSE port 15.4 watts 30 watts 60 watts 100 watts
Minimum Voltage at PoE/PD port input* 37.0 VDC 42.5 VDC 42.5 VDC 41.1 VDC
Minimum Power at PoE/PD port* 12.95 watts 25.5 watts 51 watts 71 watts
* at 100 meters using Cat5




Ordering


Step 1: Choose the Base Part Number (xxxxB-x-xx-pt)

OmniConverter 10GPoEBT/M Models
Model NumberDescription
3160B-0-24-pt OmniConverter 10GPoEBT/M 2 x SFP/SFP+ uplink port and 4 x RJ-45 IEEE 802.3bt 60W user ports
3162B-0-24-pt OmniConverter 10GPoEBT/M 2 x SFP/SFP+ uplink port and 4 x RJ-45 IEEE 802.3bt 100W user ports
 Contact Omnitron for other fiber options. Order the appropriate SFPs separately. Visit the Optical Transceivers web page.

 Step 2: Choose the Power Option (xxxxB-x-xx-pt) 

 1 = External AC/DC Adapter, 100 - 240 VAC included, with US Power Cord 
 2 = External AC/DC Adapter, 100 - 240 VAC included, No Power Cord 
 8 = External AC/DC Adapter, 100 - 240 VAC included, PS JET/PSE Certified, with Japanese Power Cord 
 9 = Direct DC 2 pin terminal connector, no AC/DC power adapter 

Step 3: Choose the Operating Temperature Range Option (xxxxB-x-xx-pt)

<leave blank> = Commercial temperature (0 to 50°C)
 W = Wide temperature (-40 to 60°C)
 Z = Extended temperature (-40 to 75°C) - not available for models with AC/DC Power Adapters

 

Accessories

Model NumberDescription
8251-0 DIN-Rail Mounting Clip
8260-0 19" rack mount shelf




Documents


pdf OmniConverter 10GPoEBT/M (Quick Start) (917 KB)

pdf OmniConverter 10GHPoEBT/M (Data Sheet) (754 KB)

 

pdf OmniConverter Command Line Interface (User Manual) (1.71 MB)

pdf OmniConverter Web Interface (User Manual) (8.48 MB)

pdf OmniConverter / RuggedNet 2.5 Hierarchical CLI (User Manual) (1.71 MB)